首页 › Arduino › 问题：Arduino LCD温度控制程序，7号端口无效（减键无效）怀疑程序，大神求解

Zeroi 发表于 2014-6-8 01:36:22

问题：Arduino LCD温度控制程序，7号端口无效（减键无效）怀疑程序，大神求解

本帖最后由 Zeroi 于 2014-6-8 01:43 编辑

程序如下: int bPin = 7;无效，试着7.8互换后还是只能加不能减

// Project 22 - LCD Thermostat

#include <LiquidCrystal.h>

#define beta 4090 // from your thermistors datasheet
#define resistance 10

// LiquidCrystal display with:
// rs on pin 12
// rw on pin 11
// enable on pin 10
// d4-7 on pins 5-2
LiquidCrystal lcd(11, 10, 9, 5, 4, 3, 2);

int ledPin = A1;
int relayPin = A2;
int aPin = 8;
int bPin = 7;
int buttonPin = 6;
int analogPin = 0;

float setTemp = 10.0;
float measuredTemp;
char mode = 'C';      // can be changed to F
boolean override = false;
float hysteresis = 0.25;

void setup()
{
lcd.begin(2, 20);
pinMode(ledPin, OUTPUT);
pinMode(relayPin, OUTPUT);
pinMode(aPin, INPUT);
pinMode(bPin, INPUT);
pinMode(buttonPin, INPUT);
lcd.clear();
}

void loop()
{
static int count = 0;
measuredTemp = readTemp();
if (digitalRead(buttonPin))
{
    override = ! override;
    updateDisplay();
    delay(500); // debounce
}
int change = getEncoderTurn();
setTemp = setTemp + change * 0.1;
if (count == 1000)
{
    updateDisplay();
    updateOutputs();
    count = 0;
}
count ++;
}

int getEncoderTurn()
{
// return -1, 0, or +1
static int oldA = LOW;
static int oldB = LOW;
int result = 0;
int newA = digitalRead(aPin);
int newB = digitalRead(bPin);
if (newA != oldA || newB != oldB)
{
    // something has changed
    if (oldA == LOW && newA == HIGH)
    {
      result = -(oldB * 2 - 1);
    }
}
oldA = newA;
oldB = newB;
return result;
}

float readTemp()
{
long a = analogRead(analogPin);
float temp = beta / (log(((1024.0 * resistance / a) - 10.0) / 10.0) + (beta / 298.0)) - 277.0;
return temp;
}

void updateOutputs()
{
if (override ||measuredTemp < setTemp - hysteresis)
{
    digitalWrite(ledPin, LOW);
    digitalWrite(relayPin, HIGH);
}
else if (!override && measuredTemp > setTemp + hysteresis)
{
    digitalWrite(ledPin, HIGH);
    digitalWrite(relayPin, LOW);   
}
}

void updateDisplay()
{
lcd.setCursor(0,0);
lcd.print("Actual: ");
lcd.print(adjustUnits(measuredTemp));
lcd.print(" o");
lcd.print(mode);
lcd.print(" ");

lcd.setCursor(0,1);
if (override)
{
    lcd.print("OVERRIDE ON   ");
}
else
{
    lcd.print("Set:    ");
    lcd.print(adjustUnits(setTemp));
    lcd.print(" o");
    lcd.print(mode);
    lcd.print(" ");
}
}

float adjustUnits(float temp)
{
if (mode == 'C')
{
    return temp;
}
else
{
    return (temp * 9) / 5 + 32;
}
}

查看完整版本: 问题：Arduino LCD温度控制程序，7号端口无效（减键无效）怀疑程序，大神求解