首页 › Arduino › 谁帮我看一下代码，谢谢

a6641 发表于 2016-2-15 22:06:54

谁帮我看一下代码，谢谢

本帖最后由 a6641 于 2016-2-15 22:10 编辑

#include <Ethernet.h>
#include <WiFi.h>
#include <SPI.h>
#include <HttpClient.h>
#include <yl_data_point.h>
#include <yl_device.h>
#include <yl_w5100_client.h>
#include <yl_wifi_client.h>
#include <yl_messenger.h>
#include <yl_sensor.h>
#include <yl_value_data_point.h>
#include <yl_sensor.h>
#include <Wire.h>
#include <Adafruit_BMP085.h>
#include "DHT.h"
#include <math.h>

#define DHTPIN 2   // what pin we're connected to
int BH1750address = 0x23;
byte buff;

// Uncomment whatever type you're using!
//#define DHTTYPE DHT11   // DHT 11
#define DHTTYPE DHT22   // DHT 22(AM2302)
//#define DHTTYPE DHT21   // DHT 21 (AM2301)

Adafruit_BMP085 bmp;
DHT dht(DHTPIN, DHTTYPE);
yl_device ardu(164872);
yl_sensor generic(183023, &ardu);
yl_sensor generic(183049, &ardu);
yl_sensor generic(183050, &ardu);
yl_sensor generic(381365, &ardu);
//replace first param value with ur u-apikey
yl_w5100_client client;
yl_messenger messenger(&client, "u-apikey", "api.yeelink.net");
personal_info_dp qinqingege("personal_info");

void setup() {
// put your setup code here, to run once:
Serial.begin(9600);//for output information
byte mac[] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xAA};
Ethernet.begin(mac);
   bmp.begin();
dht.begin();
}

void loop() {
// put your main code here, to run repeatedly:
uint16_t val=0;
BH1750_Init(BH1750address);
delay(200);
if(2==BH1750_Read(BH1750address))
{
    val=((buff<<8)|buff)/1.2;
}

Serial.print("Sensor value is: ");
Serial.println((int)val);

return val;
}

int BH1750_Read(int address) //
{
int i=0;
Wire.beginTransmission(address);
Wire.requestFrom(address, 2);
while(Wire.available()) //
{
    buff = Wire.read();// receive one byte
    i++;
}
Wire.endTransmission();
return i;
}

void BH1750_Init(int address)
{
Wire.beginTransmission(address);
Wire.write(0x10);//1lx reolution 120ms
Wire.endTransmission();
Serial.print("Temperature = ");
    Serial.print(bmp.readTemperature());
    Serial.println(" *C");
   
    Serial.print("Pressure = ");
    Serial.print(bmp.readPressure());
    Serial.println(" Pa");
    float h = dht.readHumidity();

// check if returns are valid, if they are NaN (not a number) then something went wrong!
if (isnan(t) || isnan(h)) {
    Serial.println("Failed to read from DHT");
} else {
    Serial.print("Humidity: ");
    Serial.print(h);
    Serial.print(" %\t");
}
}

Ansifa 发表于 2016-2-15 23:09:51

看完了

Super169 发表于 2016-2-16 11:38:16

看完了 X2

asdfcgdc 发表于 2016-2-16 15:00:47

不就一段代码吗？

a6641 发表于 2016-2-20 17:27:47

我指的是修改一下

查看完整版本: 谁帮我看一下代码，谢谢