MPR121 触摸传感器模块
MPR121 是一款触摸传感器芯片，原理是通过检测电容变化来判断当前是否有触摸（接近）。主要电器特性如下【参考1】：
1. 工作电压1.71-3.6v(芯片工作电压)
2. 通讯接口为 I2C
3. 12个检测端口
4. 带有1个 IRQ端口
我是在Taobao购买的模块，价格是16元【参考3】。经过搜索，这是仿sparkfun的，更多资料可以在【参考2】看到。
模块长得下面这样，有一个降压芯片，看起来可以直接使用 5V 供电。上面有12个口，可以接12个触摸按钮。IRQ 的作用是发出中断通知上面有触摸。ADD是芯片的I2C地址选择，接GND VDD SDA或者 SCL 地址分别是 0x5A 0x5B 0x5C 和 0x5D【来自参考4】。
图片来自【参考2】
下面的代码可以正常工作（卖家的例程，有一些修改可以在 1.6.0 上编译通过）
#include "mpr121.h"
#include <Wire.h>
#define SENSORS 13
#define TOU_THRESH 0x1F
#define REL_THRESH 0x1A
#define PROX_THRESH 0x3f
#define PREL_THRESH 0x3c
// variables: capacitive sensing
bool touchStates; // holds the current touch/prox state of all sensors
bool activeSensors = {1,1,1,1,1,1,1,1,1,1,1,1,1}; // holds which sensors are active (0=inactive, 1=active)
bool newData = false; // flag that is set to true when new data is available from capacitive sensor
int irqpin = 2; // pin that connects to notifies when data is available from capacitive sensor
void setup(){
// attach interrupt to pin - interrupt 1 is on pin 2 of the arduino (confusing I know)
attachInterrupt(0, dataAvailable, FALLING);
// set-up the Serial and I2C/Wire connections
Serial.begin(9600);
Wire.begin();
// set the registers on the capacitive sensing IC
setupCapacitiveRegisters();
}
void loop(){
readCapacitiveSensor();
}
/**
* dataAvailable Callback method that runs whenever new data becomes available on from the capacitive sensor.
* This method was attached to the interrupt on pin 2, and is called whenever that pins goes low.
*/
void dataAvailable() {
newData = true;
}
/**
* readCapacitiveSensor Reads the capacitive sensor values from the MP121 IC. It makes a request to
* the sensor chip via the I2C/Wire connection, and then parses the sensor values which are stored on
* the first 13 bits of the 16-bit response msg.
*/
void readCapacitiveSensor(){
if(newData){
Serial.println("yes");
//read the touch state from the MPR121
Wire.requestFrom(0x5A,2);
byte tLSB = Wire.read();
byte tMSB = Wire.read();
uint16_t touched = ((tMSB << 8) | tLSB); //16bits that make up the touch states
for (int i = 0; i < SENSORS; i++){// Check what electrodes were pressed
if (activeSensors == 0) continue;
char sensor_id [] = {'\0','\0','\0'};
switch (i) {
case 12:
sensor_id = 'P';
break;
default:
if (i < 10) {
sensor_id = char( i+48 );
}
else if (i < 12) {
sensor_id = char('1');
sensor_id = char( ( i % 10 ) + 48 );
}
}
if (sensor_id != '\0') {
// read the humidity level
// if current sensor was touched (check appropriate bit on touched var)
if(touched & (1<<i)){
// if current pin was not previously touched send a serial message
if(touchStates == 0){
Serial.print(sensor_id);
Serial.print(":");
Serial.println("1");
}
touchStates = 1;
} else {
// if current pin was just touched send serial message
if(touchStates == 1){
Serial.print(sensor_id);
Serial.print(":");
Serial.println("0");
}
touchStates = 0;
}
}
}
newData = false;
}
}
/**
* setupCapacitiveRegisters Updates all of configurations on the MP121 capacitive sensing IC. This includes
* setting levels for all filters, touch and proximity sensing activation and release thresholds, debounce,
* and auto-configurations options. At the end it activates all of the electrodes.
*/
void setupCapacitiveRegisters(){
set_register(0x5A, ELE_CFG, 0x00);
// Section A - filtering when data is > baseline.
// touch sensing
set_register(0x5A, MHD_R, 0x01);
set_register(0x5A, NHD_R, 0x01);
set_register(0x5A, NCL_R, 0x00);
set_register(0x5A, FDL_R, 0x00);
// prox sensing
set_register(0x5A, PROX_MHDR, 0xFF);
set_register(0x5A, PROX_NHDAR, 0xFF);
set_register(0x5A, PROX_NCLR, 0x00);
set_register(0x5A, PROX_FDLR, 0x00);
// Section B - filtering when data is < baseline.
// touch sensing
set_register(0x5A, MHD_F, 0x01);
set_register(0x5A, NHD_F, 0x01);
set_register(0x5A, NCL_F, 0xFF);
set_register(0x5A, FDL_F, 0x02);
// prox sensing
set_register(0x5A, PROX_MHDF, 0x01);
set_register(0x5A, PROX_NHDAF, 0x01);
set_register(0x5A, PROX_NCLF, 0xFF);
set_register(0x5A, PROX_NDLF, 0xFF);
// Section C - Sets touch and release thresholds for each electrode
set_register(0x5A, ELE0_T, TOU_THRESH);
set_register(0x5A, ELE0_R, REL_THRESH);
set_register(0x5A, ELE1_T, TOU_THRESH);
set_register(0x5A, ELE1_R, REL_THRESH);
set_register(0x5A, ELE2_T, TOU_THRESH);
set_register(0x5A, ELE2_R, REL_THRESH);
set_register(0x5A, ELE3_T, TOU_THRESH);
set_register(0x5A, ELE3_R, REL_THRESH);
set_register(0x5A, ELE4_T, TOU_THRESH);
set_register(0x5A, ELE4_R, REL_THRESH);
set_register(0x5A, ELE5_T, TOU_THRESH);
set_register(0x5A, ELE5_R, REL_THRESH);
set_register(0x5A, ELE6_T, TOU_THRESH);
set_register(0x5A, ELE6_R, REL_THRESH);
set_register(0x5A, ELE7_T, TOU_THRESH);
set_register(0x5A, ELE7_R, REL_THRESH);
set_register(0x5A, ELE8_T, TOU_THRESH);
set_register(0x5A, ELE8_R, REL_THRESH);
set_register(0x5A, ELE9_T, TOU_THRESH);
set_register(0x5A, ELE9_R, REL_THRESH);
set_register(0x5A, ELE10_T, TOU_THRESH);
set_register(0x5A, ELE10_R, REL_THRESH);
set_register(0x5A, ELE11_T, TOU_THRESH);
set_register(0x5A, ELE11_R, REL_THRESH);
// Section D - Set the touch filter Configuration
set_register(0x5A, FIL_CFG, 0x04);
// Section E - Set proximity sensing threshold and release
set_register(0x5A, PRO_T, PROX_THRESH); // sets the proximity sensor threshold
set_register(0x5A, PRO_R, PREL_THRESH); // sets the proximity sensor release
// Section F - Set proximity sensor debounce
set_register(0x59, PROX_DEB, 0x50);// PROX debounce
// Section G - Set Auto Config and Auto Reconfig for prox sensing
set_register(0x5A, ATO_CFGU, 0xC9);// USL = (Vdd-0.7)/vdd*256 = 0xC9 @3.3V
set_register(0x5A, ATO_CFGL, 0x82);// LSL = 0.65*USL = 0x82 @3.3V
set_register(0x5A, ATO_CFGT, 0xB5);// Target = 0.9*USL = 0xB5 @3.3V
set_register(0x5A, ATO_CFG0, 0x0B);
// Section H - Start listening to all electrodes and the proximity sensor
set_register(0x5A, ELE_CFG, 0x3C);
}
/**
* set_register Sets a register on a device connected via I2C. It accepts the device's address,
* register location, and the register value.
* @param address The address of the I2C device
* @param r The register's address on the I2C device
* @param v The new value for the register
*/
void set_register(int address, unsigned char r, unsigned char v){
Wire.beginTransmission(address);
Wire.write(r);
Wire.write(v);
Wire.endTransmission();
}
运行结果：
完整代码下载
参考：
1. http://wenku.baidu.com/link?url=77EtEpflHOBF9LmqwOvIwe5ONZ6I548h4BcBk4Ep1XWVO_RVDj9fycwoku44RENseV48lzvnrnDasY3UAMHsBuuU7yVdxFsAfxq-zbDiEhy MPR121中文数据手册
2. https://learn.sparkfun.com/tutorials/mpr121-hookup-guide
3. https://item.taobao.com/item.htm?spm=a1z09.2.0.0.kpoNRc&id=19968128319&_u=pkf8s90f4c
4. MPR121 DataSheet
本文 LTS 在 http://www.lab-z.com/mpr121/ 正在完这个芯片，打算做一个水位识别的，不知道多触摸同时如何工作。 li23108 发表于 2016-3-24 19:41 static/image/common/back.gif
正在完这个芯片，打算做一个水位识别的，不知道多触摸同时如何工作。
我觉得水位测试还是非接触式的比较靠谱吧？ zoologist 发表于 2016-3-24 20:09 static/image/common/back.gif
我觉得水位测试还是非接触式的比较靠谱吧？
我在优酷看到有用电容式的，类似薄膜按键那种，挺好的。今天试用了一下代码，是有点误动作，不知道灵敏度应该可以调吧，采样率之类的，资料比较少，官网的E文有些看不懂。正在研究呢。实在不行在试试超声波的。
外部粘一层塑料薄膜没问题，就是程序初始化时不输出，必须有动作时才有变化显示，看来真是不行啊，研究研究电感式的吧，这个做成音乐玩具还是很好的。
li23108 发表于 2016-3-26 08:16 static/image/common/back.gif
外部粘一层塑料薄膜没问题，就是程序初始化时不输出，必须有动作时才有变化显示，看来真是不行啊，研究 ...
恩 我打算用它作个石头剪子布的游戏看看 哥们！ 在么 你之前那个用arduino做PPT遥控器的帖子还记得吧，我想问问 里面是用的atmage8U2的单片机 ？
我看淘宝现在都是16U2的啊？是ARDUINO UNO么？
求助哥们！！
页:
[1]