在AccelStepper库中如何实现两个步进电机同步工作
本帖最后由 xboycy 于 2015-8-4 12:54 编辑// Shows how to run three Steppers at once with varying speeds
//
// Requires the Adafruit_Motorshield v2 library
// https://github.com/adafruit/Adafruit_Motor_Shield_V2_Library
// And AccelStepper with AFMotor support
// https://github.com/adafruit/AccelStepper
// This tutorial is for Adafruit Motorshield v2 only!
// Will not work with v1 shields
#include <AccelStepper.h>
#include <Wire.h>
#include <Adafruit_MotorShield.h>
#include "utility/Adafruit_PWMServoDriver.h"
Adafruit_MotorShield AFMSbot(0x61); // Rightmost jumper closed
Adafruit_MotorShield AFMStop(0x60); // Default address, no jumpers
// Connect two steppers with 200 steps per revolution (1.8 degree)
// to the top shield
Adafruit_StepperMotor *myStepper1 = AFMStop.getStepper(400, 1);
Adafruit_StepperMotor *myStepper2 = AFMStop.getStepper(400, 2);
// Connect one stepper with 200 steps per revolution (1.8 degree)
// to the bottom shield
Adafruit_StepperMotor *myStepper3 = AFMSbot.getStepper(400, 2);
// you can change these to DOUBLE or INTERLEAVE or MICROSTEP!
// wrappers for the first motor!
void forwardstep1() {
myStepper1->onestep(FORWARD, DOUBLE);
}
void backwardstep1() {
myStepper1->onestep(BACKWARD, DOUBLE);
}
// wrappers for the second motor!
void forwardstep2() {
myStepper2->onestep(FORWARD, DOUBLE);
}
void backwardstep2() {
myStepper2->onestep(BACKWARD, DOUBLE);
}
// wrappers for the third motor!
void forwardstep3() {
myStepper3->onestep(FORWARD, INTERLEAVE);
}
void backwardstep3() {
myStepper3->onestep(BACKWARD, INTERLEAVE);
}
// Now we'll wrap the 3 steppers in an AccelStepper object
AccelStepper stepper1(forwardstep1, backwardstep1);
AccelStepper stepper2(forwardstep2, backwardstep2);
AccelStepper stepper3(forwardstep3, backwardstep3);
void setup()
{
AFMSbot.begin(); // Start the bottom shield
AFMStop.begin(); // Start the top shield
stepper1.setMaxSpeed(200.0);
stepper1.setAcceleration(100.0);
stepper1.moveTo(600);
delay(1000);
stepper2.setMaxSpeed(200.0);
stepper2.setAcceleration(100.0);
stepper2.moveTo(600);
stepper3.setMaxSpeed(300.0);
stepper3.setAcceleration(100.0);
stepper3.moveTo(100);
}
void loop()
{
// Change direction at the limits
if (stepper1.distanceToGo() == 0)
{
stepper1.moveTo(400);
if (stepper1.currentPosition() == 400)
{
stepper1.moveTo(200);
}
}
if (stepper2.distanceToGo() == 0)
{
stepper2.moveTo(400);
if (stepper2.currentPosition() == 400)
{
stepper2.moveTo(200);
}
}
stepper1.run();
stepper2.run();
// stepper3.run();
}
请问，在这个程序中，如何来实现stepper2电机比stepper1电机延迟启动5秒钟啊。我试过加入delay()命令在其中多个地方，都达不到效果。（意思就是当stepper1号电机启动5秒钟之后，stepper2号电机开始启动，然后根据我的设定进入无限循环模式）。 自己顶一下，求助大神们，或者有没有其它更好的解决方案？
谢谢了……
页:
[1]