Arduino接RN-42後連接mindwave測量attention值
我的poorquality=0時LED燈會亮但為何我的Attention值一直都是0
程式碼如下
////////////////////////////////////////////////////////////////////////
// Arduino Bluetooth Interface with Mindwave
//
// This is example code provided by NeuroSky, Inc. and is provided
// license free.
////////////////////////////////////////////////////////////////////////
#define LED 13
#define BAUDRATE 57600
#define DEBUGOUTPUT 0
#define GREENLED13
#define GREENLED24
#define GREENLED35
#define YELLOWLED1 6
#define YELLOWLED2 7
#define YELLOWLED3 8
#define YELLOWLED4 9
#define REDLED1 10
#define REDLED2 11
#define REDLED3 12
#define powercontrol 10
// checksum variables
byte generatedChecksum = 0;
byte checksum = 0;
int payloadLength = 0;
byte payloadData = {
0};
byte poorQuality = 0;
byte attention = 0;
byte meditation = 0;
// system variables
long lastReceivedPacket = 0;
boolean bigPacket = false;
//////////////////////////
// Microprocessor Setup //
//////////////////////////
void setup() {
pinMode(GREENLED1, OUTPUT);
pinMode(GREENLED2, OUTPUT);
pinMode(GREENLED3, OUTPUT);
pinMode(YELLOWLED1, OUTPUT);
pinMode(YELLOWLED2, OUTPUT);
pinMode(YELLOWLED3, OUTPUT);
pinMode(YELLOWLED4, OUTPUT);
pinMode(REDLED1, OUTPUT);
pinMode(REDLED2, OUTPUT);
pinMode(REDLED3, OUTPUT);
pinMode(LED, OUTPUT);
Serial.begin(BAUDRATE); // USB
}
////////////////////////////////
// Read data from Serial UART //
////////////////////////////////
byte ReadOneByte() {
int ByteRead;
while(!Serial.available());
ByteRead = Serial.read();
#if DEBUGOUTPUT
Serial.print((char)ByteRead); // echo the same byte out the USB serial (for debug purposes)
#endif
return ByteRead;
}
/////////////
//MAIN LOOP//
/////////////
void loop() {
// Look for sync bytes
if(ReadOneByte() == 170) {
if(ReadOneByte() == 170) {
payloadLength = ReadOneByte();
if(payloadLength > 169) //Payload length can not be greater than 169
return;
generatedChecksum = 0;
for(int i = 0; i < payloadLength; i++) {
payloadData = ReadOneByte(); //Read payload into memory
generatedChecksum += payloadData;
}
checksum = ReadOneByte(); //Read checksum byte from stream
generatedChecksum = 255 - generatedChecksum; //Take one's compliment of generated checksum
if(checksum == generatedChecksum) {
poorQuality = 200;
attention = 0;
meditation = 0;
for(int i = 0; i < payloadLength; i++) { // Parse the payload
switch (payloadData) {
case 2:
i++;
poorQuality = payloadData;
bigPacket = true;
break;
case 4:
i++;
attention = payloadData;
break;
case 5:
i++;
meditation = payloadData;
break;
case 0x80:
i = i + 3;
break;
case 0x83:
i = i + 25;
break;
default:
break;
} // switch
} // for loop
#if !DEBUGOUTPUT
// *** Add your code here ***
if(bigPacket) {
if(poorQuality == 0)
digitalWrite(LED, HIGH);
else
digitalWrite(LED, LOW);
Serial.print("PoorQuality: ");
Serial.print(poorQuality, DEC);
Serial.print(" Attention: ");
Serial.print(attention, DEC);
Serial.print(" Time since last packet: ");
Serial.print(millis() - lastReceivedPacket, DEC);
lastReceivedPacket = millis();
Serial.print("\n");
switch(attention / 10) {
case 0:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, LOW);
digitalWrite(GREENLED3, LOW);
digitalWrite(YELLOWLED1, LOW);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 1:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, LOW);
digitalWrite(YELLOWLED1, LOW);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 2:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, LOW);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 3:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, LOW);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 4:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, LOW);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 5:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, LOW);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 6:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, LOW);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 7:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, LOW);
digitalWrite(REDLED3, LOW);
break;
case 8:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, HIGH);
digitalWrite(REDLED3, LOW);
break;
case 9:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, HIGH);
digitalWrite(REDLED3, HIGH);
break;
case 10:
digitalWrite(GREENLED1, HIGH);
digitalWrite(GREENLED2, HIGH);
digitalWrite(GREENLED3, HIGH);
digitalWrite(YELLOWLED1, HIGH);
digitalWrite(YELLOWLED2, HIGH);
digitalWrite(YELLOWLED3, HIGH);
digitalWrite(YELLOWLED4, HIGH);
digitalWrite(REDLED1, HIGH);
digitalWrite(REDLED2, HIGH);
digitalWrite(REDLED3, HIGH);
break;
}
}
#endif
bigPacket = false;
}
else {
// Checksum Error
}// end if else for checksum
} // end if read 0xAA byte
} // end if read 0xAA byte
}
//Mindset setup
pinMode(LED, OUTPUT);
pinMode(BLUESMIRFON, OUTPUT);
digitalWrite(BLUESMIRFON, HIGH);
Serial.begin(BAUDRATE); // USB
Serial.flush(); 邓维安 发表于 2014-3-28 09:18 static/image/common/back.gif
//Mindset setup
pinMode(LED, OUTPUT);
pinMode(BLUESMIRFON, OUTPUT);
試了
poorquality可以出來
但是我的attention值還是有問題
是因為我是用arduino uno 的關係嗎 x824172002 发表于 2014-3-30 21:05 static/image/common/back.gif
試了
poorquality可以出來
但是我的attention值還是有問題
以解決~~~謝謝喔~~~~~~~~~~~ 本帖最后由 steve136 于 2014-9-24 01:11 编辑
你好，neurosky sample code 我遇到的情況跟你一樣，看到樓上大大的解決方法，LED卻還是一直只執行到 case 0，請問大大如何解答?? :L
萬萬感謝
页:
[1]